V1.13.18 - Updates

.gitignore

@@ -1,6 +1,8 @@
 .pio
 .vscode
 venv
+.venv
+__pycache__
 .idea
 cmake-*
 CMakeLists.txt

Changelog.md

@@ -1,8 +1,17 @@
+**V1.13.18 - Updates**
+- Final changes for OAE
+
+**V1.13.17 - Updates**
+- Store AZ/ALT steps per degree and allow them to be set from Meade
+- Added more output to the InfoDisplay during boot and fixed a bug in console mode.
+- Fixed a bug that was causing the firmware to hang after a slew, if a :Q# command was issued (thanks to user c3n for tracking it down, pun intended).
+
 **V1.13.16 - Updates**
 - Throttled InfoDisplay updates. Turned off on two axis slew, limited to 5Hz on one-axis slew.
 - Guide pulses are now ignored for DEC as well when at the limits.
 
 **V1.13.15 - Updates**
+- Changes necessary for OAE, add OAE board
 - Check `INFO_DISPLAY_TYPE` builds in CI
 - Fix `INFO_DISPLAY_TYPE_I2C_SSD1306_128x64` for esp32 builds
 

Configuration.hpp

@@ -260,6 +260,8 @@
     #include "boards/RAMPS/pins_RAMPS.hpp"
 #elif (BOARD == BOARD_ESP32_ESP32DEV)
     #include "boards/ESP32_ESP32DEV/pins_ESP32DEV.hpp"
+#elif (BOARD == BOARD_OAE_V1)
+    #include "boards/ESP32_ESP32DEV/pins_OAE_V1.hpp"
 #elif (BOARD == BOARD_AVR_MKS_GEN_L_V1)
     #include "boards/AVR_MKS_GEN_L_V1/pins_MKS_GEN_L_V1.h"
 #elif (BOARD == BOARD_AVR_MKS_GEN_L_V2)

ConfigurationValidation.hpp

@@ -89,7 +89,8 @@
             #error AZ driver address for DRIVER_TYPE_TMC2209_UART not specified.
         #endif
     #endif
-
+#elif defined(OAE)
+// Valid OAE configuration
 #else
     #error Configuration does not support AZ. Use at own risk.
 #endif
@@ -110,6 +111,9 @@
         #endif
     #endif
 
+#elif defined(OAE)
+// Valid
+
 #else
     #warning Configuration does not support ALT. Use at own risk.
 #endif
@@ -193,7 +197,7 @@
         #warning Missing pin assignments for MS pins
     #endif
 #elif (DEC_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-    #if !defined(DEC_STEP_PIN) || !defined(DEC_DIR_PIN) || !defined(DEC_EN_PIN) || !defined(DEC_DIAG_PIN)
+    #if !defined(DEC_STEP_PIN) || !defined(DEC_DIR_PIN) || !defined(DEC_EN_PIN)
         // Required pin assignments missing
         #error Missing pin assignments for configured DEC DRIVER_TYPE_TMC2209_UART driver
     #endif
@@ -213,7 +217,7 @@
         #warning Missing pin assignments for MS pins
     #endif
 #elif (RA_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-    #if !defined(RA_STEP_PIN) || !defined(RA_DIR_PIN) || !defined(RA_EN_PIN) || !defined(RA_DIAG_PIN)
+    #if !defined(RA_STEP_PIN) || !defined(RA_DIR_PIN) || !defined(RA_EN_PIN)
         // Required pin assignments missing
         #error Missing pin assignments for configured RA DRIVER_TYPE_TMC2209_UART driver
     #endif
@@ -225,12 +229,12 @@
 
 #if (AZ_STEPPER_TYPE != STEPPER_TYPE_NONE)
     #if (AZ_DRIVER_TYPE == DRIVER_TYPE_A4988_GENERIC) || (AZ_DRIVER_TYPE == DRIVER_TYPE_TMC2209_STANDALONE)
-        #if !defined(AZ_STEP_PIN) || !defined(AZ_DIR_PIN) || !defined(AZ_EN_PIN) || !defined(AZ_DIAG_PIN)
+        #if !defined(AZ_STEP_PIN) || !defined(AZ_DIR_PIN) || !defined(AZ_EN_PIN)
             // Required pin assignments missing
             #error Missing pin assignments for configured AZ DRIVER_TYPE_A4988_GENERIC or DRIVER_TYPE_TMC2209_STANDALONE driver
         #endif
     #elif (AZ_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-        #if !defined(AZ_STEP_PIN) || !defined(AZ_DIR_PIN) || !defined(AZ_EN_PIN) || !defined(AZ_DIAG_PIN)
+        #if !defined(AZ_STEP_PIN) || !defined(AZ_DIR_PIN) || !defined(AZ_EN_PIN)
             // Required pin assignments missing (ATmega uses SoftwareSerial for this driver)
             #error Missing pin assignments for configured AZ DRIVER_TYPE_TMC2209_UART driver
         #endif
@@ -243,12 +247,12 @@
 
 #if (ALT_STEPPER_TYPE != STEPPER_TYPE_NONE)
     #if (ALT_DRIVER_TYPE == DRIVER_TYPE_A4988_GENERIC) || (ALT_DRIVER_TYPE == DRIVER_TYPE_TMC2209_STANDALONE)
-        #if !defined(ALT_STEP_PIN) || !defined(ALT_DIR_PIN) || !defined(ALT_EN_PIN) || !defined(ALT_DIAG_PIN)
+        #if !defined(ALT_STEP_PIN) || !defined(ALT_DIR_PIN) || !defined(ALT_EN_PIN)
             // Required pin assignments missing
             #error Missing pin assignments for configured AZ DRIVER_TYPE_A4988_GENERIC or DRIVER_TYPE_TMC2209_STANDALONE driver
         #endif
     #elif (ALT_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-        #if !defined(ALT_STEP_PIN) || !defined(ALT_DIR_PIN) || !defined(ALT_EN_PIN) || !defined(ALT_DIAG_PIN)
+        #if !defined(ALT_STEP_PIN) || !defined(ALT_DIR_PIN) || !defined(ALT_EN_PIN)
             // Required pin assignments missing (ATmega uses SoftwareSerial for this driver)
             #error Missing pin assignments for configured ALT DRIVER_TYPE_TMC2209_UART driver
         #endif

Configuration_adv.hpp

@@ -22,6 +22,15 @@
     #define BUFFER_LOGS false
 #endif
 
+#ifndef OAM
+    #ifndef OAE
+        #define OAT "OAT"
+    #endif
+#endif
+#if defined(OAE) && defined(OAM)
+    #error "OAE and OAM cannot be defined at the same time"
+#endif
+
 /////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 //                            ////////
 // MOTOR & DRIVER SETTINGS    ////////
@@ -232,14 +241,14 @@
 #endif
 
 #ifndef DEC_LIMIT_UP
-    #ifdef OAM
+    #if defined(OAM) || defined(OAE)
         #define DEC_LIMIT_UP 135.0f
     #else
         #define DEC_LIMIT_UP 0.0f
     #endif
 #endif
 #ifndef DEC_LIMIT_DOWN
-    #ifdef OAM
+    #if defined(OAM) || defined(OAE)
         #define DEC_LIMIT_DOWN 135.0f
     #else
         #define DEC_LIMIT_DOWN 0.0f
@@ -332,16 +341,34 @@
         #define AZ_STEPPER_ACCELERATION (100 * AZ_MICROSTEPPING)
     #endif
 
-    // the Circumference of the AZ rotation. 808mm dia.
+    // the Circumference of the AZ rotation. 808mm dia (OAT)
     #ifndef AZ_CIRCUMFERENCE
-        #define AZ_CIRCUMFERENCE 2538.4f
+        #ifdef OAE
+            // Roughly from the joint to the rod placement is 70mm
+            #define AZ_CIRCUMFERENCE 56.0f * 2 * PI
+            #ifndef AZ_ROD_PITCH
+                #define AZ_ROD_PITCH 0.5
+            #endif
+            #define AZIMUTH_STEPS_PER_REV                                                                                                  \
+                +(AZ_CORRECTION_FACTOR * (AZ_CIRCUMFERENCE / AZ_ROD_PITCH) * AZ_STEPPER_SPR * AZ_MICROSTEPPING)  // Actually u-steps/rev
+        #else
+            #define AZ_CIRCUMFERENCE 2538.4f
+        #endif
     #endif
+
+    #ifndef OAE
+        #define AZ_WORMGEAR_RATIO 1.0f
+    #endif
+
     #ifndef AZIMUTH_STEPS_PER_REV
         #define AZIMUTH_STEPS_PER_REV                                                                                                      \
             (AZ_CORRECTION_FACTOR * (AZ_CIRCUMFERENCE / (AZ_PULLEY_TEETH * GT2_BELT_PITCH)) * AZ_STEPPER_SPR                               \
              * AZ_MICROSTEPPING)  // Actually u-steps/rev
     #endif
-    #define AZIMUTH_STEPS_PER_ARC_MINUTE (AZIMUTH_STEPS_PER_REV / (360 * 60.0f))  // Used to determine move distance in steps
+
+    #ifndef AZIMUTH_STEPS_PER_ARC_MINUTE
+        #define AZIMUTH_STEPS_PER_ARC_MINUTE (AZIMUTH_STEPS_PER_REV / (360 * 60.0f))  // Used to determine move distance in steps
+    #endif
 
     // AZ TMC2209 UART settings
     // These settings work only with TMC2209 in UART connection (single wire to TX)
@@ -373,7 +400,7 @@
         #define ALT_MICROSTEPPING 4
     #endif
     #ifndef ALT_STEPPER_SPR
-        #define ALT_STEPPER_SPR 400  // NEMA 0.9° = 400  |  NEMA 1.8° = 200
+        #define ALT_STEPPER_SPR (400.0)  // NEMA 0.9° = 400  |  NEMA 1.8° = 200
     #endif
     #ifndef ALT_STEPPER_SPEED
         #define ALT_STEPPER_SPEED 2000
@@ -398,19 +425,30 @@
             (ALT_CORRECTION_FACTOR * (ALT_CIRCUMFERENCE / ALT_ROD_PITCH) * ALT_STEPPER_SPR * ALT_MICROSTEPPING)  // Actually u-steps/rev
 
     #else
-        // the Circumference of the AZ rotation. 770mm dia.
-        #define ALT_CIRCUMFERENCE 2419.0f
-        #if AUTOPA_VERSION == 1
-            // the ratio of the ALT gearbox for AutoPA V1 (40:3)
-            #define ALT_WORMGEAR_RATIO (40.0f / 3.0f)
-        #else
-            // the ratio of the ALT gearbox for AutoPA V2 (40:1)
-            #define ALT_WORMGEAR_RATIO (40.0f)
-        #endif
-        #ifndef ALTITUDE_STEPS_PER_REV
+        #ifdef OAE
+            #ifndef ALT_ROD_PITCH
+                #define ALT_ROD_PITCH 1.25  // mm/rev
+            #endif
+            // the Circumference of the ALT rotation. Roughly 146mm radius.
+            #define ALT_CIRCUMFERENCE 130.0f * 2 * PI
             #define ALTITUDE_STEPS_PER_REV                                                                                                 \
-                (ALT_CORRECTION_FACTOR * (ALT_CIRCUMFERENCE / (ALT_PULLEY_TEETH * GT2_BELT_PITCH)) * ALT_STEPPER_SPR * ALT_MICROSTEPPING   \
-                 * ALT_WORMGEAR_RATIO)  // Actually u-steps/rev
+                +(ALT_CORRECTION_FACTOR * (ALT_CIRCUMFERENCE / ALT_ROD_PITCH) * ALT_STEPPER_SPR                                            \
+                  * ALT_MICROSTEPPING)  // Actually u-steps/rev
+        #else
+            // the Circumference of the AZ rotation. 770mm dia.
+            #define ALT_CIRCUMFERENCE 2419.0f
+            #if AUTOPA_VERSION == 1
+                // the ratio of the ALT gearbox for AutoPA V1 (40:3)
+                #define ALT_WORMGEAR_RATIO (40.0f / 3.0f)
+            #else
+                // the ratio of the ALT gearbox for AutoPA V2 (40:1)
+                #define ALT_WORMGEAR_RATIO (40.0f)
+            #endif
+            #ifndef ALTITUDE_STEPS_PER_REV
+                #define ALTITUDE_STEPS_PER_REV                                                                                             \
+                    (ALT_CORRECTION_FACTOR * (ALT_CIRCUMFERENCE / (ALT_PULLEY_TEETH * GT2_BELT_PITCH)) * ALT_STEPPER_SPR                   \
+                     * ALT_MICROSTEPPING * ALT_WORMGEAR_RATIO)  // Actually u-steps/rev
+            #endif
         #endif
     #endif
 
@@ -620,23 +658,6 @@
 //                                  ////////
 ////////////////////////////////////////////
 
-// Stepper drivers
-#if (RA_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-    #if defined(ESP32)
-        #define RA_SERIAL_PORT Serial2  // Can be shared with DEC_SERIAL_PORT
-    #elif defined(__AVR_ATmega2560__)
-    // Uses SoftwareSerial
-    #endif
-#endif
-
-#if (DEC_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
-    #if defined(ESP32)
-        #define DEC_SERIAL_PORT Serial2  // Can be shared with RA_SERIAL_PORT
-    #elif defined(__AVR_ATmega2560__)
-    // Uses SoftwareSerial
-    #endif
-#endif
-
 // Focuser
 #if (FOCUS_DRIVER_TYPE == DRIVER_TYPE_TMC2209_UART)
     #if defined(ESP32)

Constants.hpp

@@ -18,6 +18,7 @@
 
 // ESP32 based boards
 #define BOARD_ESP32_ESP32DEV 1001
+#define BOARD_OAE_V1         1002
 
 /**
  * Supported keypad/display types. Use one of these values for DISPLAY_TYPE configuration matching your used display and keypad.

LocalConfiguration.hpp

@@ -16,6 +16,8 @@
     #include "Configuration_local_mksgenlv1.hpp"
 #elif BOARD == BOARD_ESP32_ESP32DEV && __has_include("Configuration_local_esp32dev.hpp")
     #include "Configuration_local_esp32dev.hpp"
+#elif BOARD == BOARD_OAE_V1 && __has_include("Configuration_local_oae.hpp")
+    #include "Configuration_local_oae.hpp"
 #elif __has_include("Configuration_local.hpp")
     #include "Configuration_local.hpp"
 #endif

Version.h

@@ -3,4 +3,4 @@
 // Also, numbers are interpreted as simple numbers.                        _   __   _
 // So 1.8 is actually 1.08, meaning that 1.12 is a later version than 1.8.  \_(..)_/
 
-#define VERSION "V1.13.16"
+#define VERSION "V1.13.18"